The Smart Marty Sky Dispatch
FAA halts router installation following nationwide ground stop, root cause of issue unknown
The FAA is halting the installation of Juniper routers following last week's nationwide ground stop, an agency spokesperson confirmed to ABC News on Tuesday.
The FAA paused the installation of Juniper routers as part of its copper-to-fiber modernization program, following a nationwide ground stop on outbound departures that affected U.S. air travel operations. The pause was described by an FAA spokesperson to ABC7 New York as a temporary halt, not a permanent suspension, and was issued after an extended ground stop that restricted new outbound departures while aircraft already in flight continued under the last assigned clearances. No cause for the ground stop or the router installation halt was disclosed in the material provided.
ABC News reported that the pause came after the nationwide ground stop and an internal review of router-related infrastructure, with the FAA characterizing the action as a pause and not providing a timeline for resuming installations or details on which flight operations were affected. The broader context described by multiple outlets notes that outbound departures across U.S. airports were halted while in-flight movements continued under ATC Zero procedures, with international arrivals to be processed on a case-by-case basis as conditions evolved.
Investigators traced the disruption to data traffic surges from FAA facilities involved in the fiber upgrade, focusing on a router replacement activity at a site in El Dorado, Arkansas where a Juniper router installed by L3Harris was linked to disrupted communications and radar feeds at 17 of the FAA’s 22 en route centers. Additional router activity at Amarillo, Texas, was cited as a contributing factor in the cascading effect, according to AVweb’s synthesis of reporting cited by multiple outlets.
The disruption prompted Senate lawmakers, led by Sen. Maria Cantwell and consisting of thirteen Democrats on the Senate Commerce Committee, to urge the FAA to pause further router deployments pending safety and reliability reviews. Reports indicate that about 3,648 routers were slated for conversion to Juniper devices, with roughly 400 installed and 69 reported operational at the time of inquiries. The calls for caution reflect concerns about safety implications as thousands of conversions remained pending.
San Francisco International Airport emerged as a notable hotspot within the disruption, with outlets reporting more than 30 outbound flights grounded as part of the nationwide ground stop. Coverage emphasizes the scale of airport-level disruption and notes that in-flight handling continued under ATC Zero, but does not provide specific flight numbers or aircraft details tied to particular incidents. The situation affected other hubs as well, with reports indicating outbound restrictions at major airports like Chicago O’Hare during the initial phase.
Fox Business reported that the FAA paused router installations nationwide after a Friday ground stop was tied to a tech issue. L3Harris installed a new router at a radio transmitter site in Arkansas on Friday, and officials said the router began sending an excess of connection signals, overwhelming the network and interfering with air traffic communications, which helped trigger the ground stop. The FAA’s review identified a second problematic router in Texas, leading to isolation of those routers to stabilize the system, and the agency disabled the broadcasting functionality on more than 60 similar routers during the investigation.
The Wall Street Journal echoed the characterization of the situation as an extraordinary safety precaution and noted that air-traffic-control operations were analyzed under ATC Zero, allowing aircraft already in flight to proceed under the last assigned clearances, with no specified end time for resuming normal operations. Investigations were described as focusing on whether the disruption stemmed from faulty equipment or the installation process itself, and the FAA disabled similar functionality on roughly 60 other routers as part of stabilization efforts.
LiveNOW from FOX reported that a distant FAA location’s router installation triggered a data-traffic surge that cascaded into the nationwide ground stop and widespread flight cancellations and delays. Investigators were described as reviewing causes and impacts as part of the ongoing inquiry, while Axios framed the stop as ATC Zero intended to pause new outbound movements during the review of air-traffic-control operations and upgrades.
Overall reporting linked the outages to the copper-to-fiber modernization and associated router replacements by L3Harris, with some outlets noting that more than 70% of the planned airspace communication conversion had been completed. The coverage described aging infrastructure and legacy technology as contributing factors, and reported that the end of the initial advisory window for resuming normal departures remained undetermined, with international arrivals to be handled on a case-by-case basis as conditions evolved.